Ex rental and used production company stock

Buy at rock bottom prices, save on hire fees

Sound Equipment

Microphones, mixers, speakers and accessories

Lighting Equipment

Spotlights, floodlights, PAR cans, stands, dimmers and mixing desks

Save the planet and save money too

Go green, re-cycling is environmentally friendly

Hurry, don't delay!

Offers are strictly limited, buy now whilst stocks last

Sunday, 26 October 2014

Sold - 8U amp rack flight case - £70

This flight case, with an 8U capacity, is the perfect size for transporting; audio amplifiers, lighting dimmer racks, power distribution panels or other large and weighty kit.


For sale 8U flight case - cheap and practical for £70


The external dimensions are; 42 cm x 53 cm x 59 cm, a practical size which can be transported in a car if needed.

The case is constructed from heavy duty ply, with in a aluminium sheet, stucco textured finish on the outside.
It has 4 large recessed industrial grade butterfly catches, 2 spring loaded recessed flip handles, ball corners and a sturdy wheel board with 4 x 75mm industry standard non-marking castors.
There may be some light surface patination and bits of wear and tear, but everything works as it should.

For sale 8U flight case - sturdy wheel board with 4 x 75mm castors

Both the front and rear covers can be removed, rack strips are fitted to both the front and rear sections. The depth between the rack strips is 38cm, note that the end covers are quite deep, so deep casings as used on some audio amplifiers can still be accommodated. The rack strip on the front is 8U, but I have mounted 9U of kit inside it before, as there is sufficient clearance, the rack strip on the rear is 6U and was installed to a mount power distribution unit and custom input/output patch panels.

For sale 8U flight case - deep audio amplifiers can be accommodated

It came with a hole in one corner where someone had mounted an IEC mains inlet connector.
This type of heavy duty road rack style flight case would cost from £150 upwards new. I have priced it at £70 for a speedy sale, the castors alone would cost half this price alone.

For sale 8U flight case - an IEC mains inlet connector goes here

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES:

23/12/16 - Now Sold

Sunday, 19 October 2014

Sold - Jumbo road trunk flight case - £99

There are large flight cases and then there are oversized flight cases, if this particular one was a person, it would have to be the strong man Geoff Capes.

Jumbo flight case for sale - the Geoff Capes of flight cases

The dimensions are; 119 cm x 60 cm x 86 cm, a very generous size, bigger than my car trailer and not something you're going to squeeze inside a car; needless to say, when packed it will be quite a weight.

The flight case is constructed from ply, covered in a satin black finish. The hinged lid is secured by 2 large, recessed, industrial grade butterfly catches, complemented by spring loaded recessed flip handles, heavy duty corners and 4 x 100mm castors with blue non-marking wheels.

There is some foam lining and plywood sections remaining from their original purpose, obviously this can be removed to make extra space for cables, etc.
There is some minor surface patina on the metal parts and bits of wear and tear, but everything works properly.
This type of heavy duty road trunk style flight case would cost from £200 upwards new. I have priced this at £99 for a speedy sale, the castors alone would cost around £80.

Jumbo flight case for sale - only £99

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES:

21/10/14 - Under offer, subject to delivery.
23/10/14 - Now Sold.

Saturday, 18 October 2014

Sold - Leonovo 90W Laptop Power Supply - £9

This is the power supply for a Lenovo laptop, the part number is 42T4428, I shouldn't need to say, but please make certain that it is correct for your model of laptop.
The output voltage is 20 Volts and the total power output is 90 Watts, it will be supplied complete with a C5 "Clover leaf" style mains cable and plug.


For Sale -  Leonovo laptop power supply unit - £9

A spare power supply is always handy, leave one at work and save carrying weight when commuting.
The price of £9 includes recorded delivery within the UK.

Send a message or leave a comment if you have any enquiries.


Updates:

12/11/2017 - Now sold

Tuesday, 7 October 2014

Sold - Budget Road Trunk Flight Cases - £80 each

Following this post I was told that for some, £99 for a road trunk flight case is still too expensive, so what could I do for £80? Ever keen to please, I can offer this pair of flight cases at £80 each, but absolutely no further offers or haggling all-right!

Budget road trunks for sale - big enough for 6 small speakers

They were used for carrying 3 pairs of EV Sx80 speakers as a modular show item. I will need to confirm the dimensions, but I believe them to be; 100 cm x 50 cm x 50 cm, a very practical size.

Budget road trunks for sale - a practical size

The flight case is constructed from ply, covered in a satin grey, plastic, veneer. The hinged lid is secured by 2 large, recessed, industrial grade butterfly catches, complemented by 4 spring loaded recessed flip handles, heavy duty corners and 4 x 100mm castors with non-marking wheels.

Budget road trunks for sale - plywood internal dividers can be removed

There is some minor surface patina on the metal parts and bits of wear and tear, but everything works properly. There are lightweight plywood internal dividers and foam which can be removed prior to sale if you want them. They were originally owned by Promuseast and still have the odd stencilled logo or two and the original tour label, as with other items for sale here, these will be removed.

Budget road trunks for sale -still in good condition

This type of heavy duty road trunk style flight case would cost from £200 upwards new. I have priced this at £80 for a speedy sale, the castors alone would cost around £80.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES:

19/10/14 - One has been "dibbed" awaiting payment, still one more left.
23/10/14 - One sold, only one more left, be quick people.
04/04/19 - Sold out

Monday, 6 October 2014

For Sale - Flat screen TV Flight Case Regular Size - £99

Here is the next of the batch of plasma / lcd / led flat screen cases coming up for sale, as they are now surplus to our requirements. There will be a few available in this size, which could be handy if you have a "fleet" to send out on the road.

Flight cases for sale -  for plasma, lcd or led flat screens

The dimensions are; 115 cm x 79 cm x 45 cm, bear in mind that this is going to be quite a squeeze to fit inside a car and when packed will be quite a weight to load on your own; of course if you have a van with a ramp or a tail-lift it will be a breeze.

Flight cases for sale -  black hex board ply construction

The flight case is constructed from black hex board ply. The lift off lid is secured by 4 large, recessed, industrial grade butterfly catches, complemented by 6 spring loaded recessed flip handles, heavy duty corners and 4 x 100mm very nice Guitel brand castors with blue non-marking wheels

There is some foam lining remaining from their original purpose, obviously this can be removed to make extra space for cables, etc.

Flight cases for sale -  some wear but everything works

There is some minor surface patina on the metal parts and bits of wear and tear, but everything works properly. It was originally owned by Promuseast and still has the odd stencilled logo or two and the original tour label, as with other items I have sold previously, it will be de-branded prior to sale.

Flight cases for sale -  internal foam for a 42" plasma screen

This type flight case would cost from £200 upwards new. I have priced this at £99 for a speedy sale, the castors alone would cost around £70.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES

20/10/14 - First serious enquiry, awaiting confirmation, payment and delivery.
23/10/14 - 2 Now sold, just 1 more of this type left in stock, be quick people.

Sunday, 5 October 2014

Sold - Flat screen TV or monitor case slim type - £90

This is the first of a batch of plasma / lcd / led flat screen cases coming up for sale, as they are now surplus to our requirements. It is slightly skinnier than the others and is the only one available in this size.

Plasma flight case for sale - 120 cm x 81 cm x 36 cm

The dimensions are; 120 cm x 81 cm x 36 cm, bear in mind that this is going to be quite a squeeze to fit inside a car and when packed will be quite a weight to load on your own; of course if you have a van with a ramp or a tail-lift it will be a breeze.

Flat screen tv flight case for sale - ply construction, black gloss finish

The flight case is constructed from ply, covered in a black gloss, plastic veneer. The lift off lid is secured by 4 large, recessed, industrial grade butterfly catches, complemented by 6 spring loaded recessed flip handles, heavy duty corners and 4 x 75mm castors with black non-marking wheels. 2 of the castors are locking for added security when in transit.

There is some foam lining remaining from their original purpose, obviously this can be removed to make extra space for cables, etc.

LCD monitor flight case for sale - 6 spring loaded recessed flip handles

There is some minor surface patina on the metal parts and bits of wear and tear, but everything works properly. It was originally owned by Promuseast and still has the odd stencilled logo or two and the original tour label, as with other items I have sold previously, it will be de-branded prior to sale.

This type flight case would cost from £200 upwards new. I have priced this at £90 for a speedy sale, the castors alone would cost around £70.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES

10/04/16 - Now Sold

Sunday, 27 April 2014

Sold - Touring amp rack flight case #2 - £120

Another day, another flight case and one of the three similar "tall" rack flight cases coming up for sale. Much like the others, it would be ideally suited to housing lighting dimmer racks, power distribution panels or audio amplifiers.

Rack flight case - dimmer racks or audio amplifiers?
The dimensions are; 95 cm x 52 cm x 66 cm, which is a substantial size, do bear in mind that this is quite a large item to fit in a car and will weigh a lot once fully loaded.

Rack flight case - heavy duty ply construction

The case is constructed from heavy duty ply, with a dark chocolate brown colour, textured finish, on the outside and a glossy Formica finish on the inside.
It has 8 large recessed industrial grade butterfly catches, 2 spring loaded recessed flip handles, heavy duty ball corners, wheel boards with 8 x 100mm castors and industry standard non-marking castors.

Rack flight case for sale - with heavy duty castors

Both the front and rear covers can be removed, the rear cover is fitted with castors in addition to the base. This has the advantage that the unit can be moved around on stage in its normal orientation, but also be moved safely "on its back" whilst in transit. It is so robust that you can place additional items on the case and use it as handy trolley for your load ins and outs.
Rack strips are fitted to both the front and rear sections.

Rack flight case - both front and rear covers removable

There may be some light surface patination and bits of wear and tear, but everything works as it should.

In addition an IEC connector power distribution and conditioning system is installed along with a rack drawer and, wait for it, a cassette recorder, yay!

Rack flight case - draw included

They are a couple of stencilled corporate branding logos, there is a tour label on the top.


Rack flight case for sale  - built in power distributor

This type of heavy duty road rack style flight case would cost from £250 upwards new. I have priced it at £120 for a speedy sale, the castors alone would cost around this much.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES:

23/01/14 - Now Sold

Saturday, 26 April 2014

Sold - Manfrotto wind up lighting stands case - £69

Here's another road-show favourite from back in the day and in my humble opinion is the safest way to transport a pair of heavy duty wind up stands. It is much easier to wheel into the venue than something in a bag or loose. Your precious equipment is going to last a lot longer and your hard earned earnings go a lot further with this flight case. So, let's get down to specifics.

Flight case - equipment will last longer

The dimensions are; 183 cm x 39 cm x 33 cm, a very generous size, but do bear in mind that this is going to be too large to fit in a car and when packed will be quite a weight.

The flight case is constructed from ply, covered in a satin black, plastic veneer. The hinged lid is secured by 2 large, recessed, industrial grade butterfly catches, complemented by 2 spring loaded recessed flip handles, heavy duty corners and 4 x 100mm castors with blue rubber non-marking wheels.

There are a couple of ply divider/supports to keep a pair of Manfrotto wind up lighting stands in place whilst in transit. They can be easily removed should they not suit your purposes.

Flight case - plywood dividers to support wind-up lighting stands

There is some minor surface patination of the metal parts, and bits of wear and tear, but everything still works properly.

It was originally owned by Promuseast and still has the odd stencilled logo or two and the original tour label.

Flight case - suits Manfrotto wind up lighting stands

This type of heavy duty road trunk style flight case would cost from £150 upwards new. I have priced this at £69 for a speedy sale, the castors alone would cost around £80.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES:

18/10/14 - This has been "dibbed"subject to inspection, payment and collection.
22/10/14 - Now sold.

Friday, 25 April 2014

Sold - Large road trunk flight case - £99

Continuing the oversized flight case theme, this beast was a favourite for many road-shows and had plenty of room to carry all our; laptops, switchers, monitors and all manner of bits and bobs.

Large road trunk -  plenty of room to carry all manner of bits and bobs

The dimensions are; 126 cm x 60 cm x 60 cm, a very generous size, but do bear in mind that this is going to be quite a squeeze to fit inside a car and when packed will be quite a weight.

Large road trunk - a very generous size

The flight case is constructed from ply, covered in a satin grey, plastic, veneer. The hinged lid is secured by 2 large, recessed, industrial grade butterfly catches, complemented by 4 spring loaded recessed flip handles, heavy duty corners and 4 x 100mm castors with black non-marking wheels.

There is some foam lining remaining from their original purpose, obviously this can be removed to make extra space for cables, etc.

Large road trunk - plastic veneer on ply construction

There is some minor surface patina on the metal parts and bits of wear and tear, but everything works properly.
It was originally owned by Promuseast and still has the odd stencilled logo or two and the original tour label.

This type of heavy duty road trunk style flight case would cost from £200 upwards new. I have priced this at £99 for a speedy sale, the castors alone would cost around £80.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES:

13/05/14 - Under offer, subject to collection 17-05-14
17/05/14 - Buyer too broke to collect! So back on sale, plus it has now been cleaned up and all graphics removed
18/10/14 - Now "dibbed" subject to payment and delivery.
23/10/14 - Now Sold.



Large road trunk - would cost from £200 upwards new

Thursday, 24 April 2014

Sold - Touring amp rack flight case #1 - £120

Continuing on the flight case theme, this will be the first of at least three similar "tall" rack flight cases on offer. This particular case is the most heavy duty of the three and would be ideally suited to housing lighting dimmer racks, power distribution panels  or audio amplifiers.
The dimensions are; 97 cm x 52 cm x 69 cm, which is a substantial size, do bear in mind that this is quite a large item to fit in a car and will weigh a lot once fully loaded.

Rack flight case -  a substantial size

The case is constructed from heavy duty ply, covered in a satin black, plastic finish.
It has 8 large recessed industrial grade butterfly catches, no fewer than 12 spring loaded recessed flip handles, heavy duty ball corners, wheel boards with 8 x 100mm castors and industry standard non-marking castors. Those on the back panel are in very good condition, those on the base are serviceable.
Both the front and rear covers can be removed, the rear cover is fitted with castors in addition to the base. This has the advantage that the unit can be moved around on stage in its normal orientation, but also be moved safely "on its back" whilst in transit. It is so robust that you can place additional items on the case and use it as handy trolley for your load ins and outs.
21 Unit high rack strips are fitted to both the front and rear sections. The top has 4 riveted studs that enabled a sub-rack to be mounted securely on top.

Rack flight case - castors on the back and the base

There may be some light surface patina and bits of wear and tear, but everything still works as it should.
They are no corporate branding logos or sign writing, there is a tour label on the top.

Rack flight case - 21U of space

This type of heavy duty road rack style flight case would cost from £250 upwards new. I have priced it at £120 for a speedy sale, the castors alone would cost around this much.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES

17/05/14 - I took away the branding today, it's now all black. This is such a heavy duty and well made item, I can't believe it hasn't been snapped up by now. Ho hum.
28/09/14 - Now under offer.
03/10/14 - Sold.

Wednesday, 23 April 2014

For Sale - Extra large road trunk flight case - £99

It has been a while since I have listed any new flight cases, but it is now very much the time to make up for that, there will be plenty listed over the next week. First up is this extra large flight case, originally designed for a giant video projector, but re-purposed in more recent years for carrying just about anything; from plasma screens, to rope and post barrier systems and even heavy duty mains distribution cables.

Extra large road trunk - carry just about anything

The dimensions are; 136 cm x 66 cm x 40 cm, a very generous size, but do bear in mind that this is going to be quite a squeeze to fit in a car and when packed will be quite a weight.


Extra large road trunk - Everything works

The flight case is constructed from heavy duty ply, covered in a satin grey, patterned plastic, veneer. The hinged lid is secured by 3 large, recessed, industrial grade butterfly catches, complemented by 4 spring loaded recessed flip handles, heavy duty corners and 4 x 100mm castors with non-marking wheels.

There is some foam lining remaining from their original purpose, obviously this can be removed to make extra space for cables, etc.

Extra large road trunk - some foam lining remains

There is some surface patina on the metal parts and bits of wear and tear, but everything still works properly. It was originally owned by Blitz and still has the odd logo and the original touring label.

This type of heavy duty road trunk style flight case would cost from £200 upwards new. I have priced this at £99 for a speedy sale, the castors alone would cost around £80.

I can arrange personal delivery for the following cost:
  • Within the M25 - No charge
  • 50 miles from London (e.g. Brighton) - £20
  • 100 miles from London (e.g. Coventry) - £30
  • 200 miles from London (e.g. Sheffield) - £60
  • 300 miles from London (e.g. Newcastle) - £90
If you want to inspect them before making a purchase drop me a line via the contact page here


UPDATES:

None so far

Tuesday, 22 April 2014

Sold - Sennheiser VHF tie clip radio microphone 2 of 2 - £69

So this the second of two VHF radio microphone kits I have to clear. Some might regard these items as being somewhat archaic, but Sennheiser are the Rolls Royce of microphone manufacturers and even the oldest and most budget orientated models will perform better than a great deal of inexpensive modern equipment from certain parts of the World.

These are VHF units and utilise shared frequencies that aren't subject to any of the recent re-allocation of the radio spectrum and are unlikely to be sold off for mobile use in the foreseeable future. This unit can be switched to work on either of two frequencies, in this instance; 173.800 or 174.100 Mhz.

VHF radio mic kit - this set can operate on 173.800 or 174.100 Mhz

There is an On/Off switch on the transmitter and an attenuator that will drop the signal going to the pre-amp to enable the unit to be used with high level signals, such as acoustic musical instruments. I recall seeing these used successfully with brass and woodwind instruments. It is powered by a 9 Volt PP3 battery, with a good alkaline one it will give around 6 hours of continuous use.

The transmitter antenna is captive and can't be removed, so it's one less connection to break or get lost. The tie clip (lavalier) microphone is detachable and uses a Lemo connector, you can find out more about Lemo connectors for radio microphones here.

The receiver unit has meters to show received RF (radio) and AF (audio) levels, which of the two antennae are active and that the unit is receiving power. Squelch is adjustable by a front mounted pot. Power is supplied by a separate "wall wart" type unit, it is conceivable that you could also power the receiver from a battery supply or vehicle "cigarette lighter" socket for location recording and film work (adapters not supplied).
There are output jacks on the back panel for balanced XLR fixed microphone level or 1/4" jack with a variable line level adjusted by a trim pot.

Two of these units can be locked together and will take up a single unit of rack space, I should be able to find you a suitable tray if this option is of interest to you.

VHF radio mic kit - just £69 for the entire kit including flight case

As there is now so much competition from (in my opinion) cheap inferior equipment from the Far East I have priced these modestly to sell at just £69 for the entire kit, which includes a lightweight flight case. Note that unlike similar systems at this price point found on eBay, this is a true diversity system with two aerials and receiver circuits to guarantee the best possible reception. The aerials can be extended to further improve reception, if you are going to be some distance from a stage or want to locate the receiver inside a rack or shielded control room. If you can find a better deal, drop me a line via the contact page and I will do my best to match it.

It will be supplied in a small lightweight flight case, with padded foam cut outs for the receiver, transmitter, power supply and a couple of batteries. The original hard copy operator's manual will also be included.

Carriage by courier is now included in the price.


UPDATES:

05/11/2016 - Now sold

Monday, 21 April 2014

Sold - Sennheiser VHF tie clip radio microphone 1 of 2 - £69

Continuing the ongoing rationalisation of the OneOneTwo.com live sound department, there will be two VHF radio microphone kits to clear. Some might regard these items as being somewhat archaic, but Sennheiser are the Rolls Royce of microphone manufacturers and even the oldest and most budget orientated models will perform better than a great deal of inexpensive modern equipment from certain parts of the World.

These are VHF units and utilise shared frequencies that aren't subject to any of the recent re-allocation of the radio spectrum and are unlikely to be sold off for mobile use in the foreseeable future. This unit can be switched to work on either of two frequencies, in this instance; 176.400 or 177.000 Mhz.


VHF radio mic kit - this set can operate on 176.400 or 177.000 Mhz

There is an On/Off switch on the transmitter and an attenuator that will drop the signal going to the pre-amp to enable the unit to be used with high level signals, such as acoustic musical instruments. I recall seeing these used successfully with brass and woodwind instruments. It is powered by a 9 Volt PP3 battery, with a good alkaline one it will give around 6 hours of continuous use.

The transmitter antenna is captive and can't be removed, so it's one less connection to break or get lost. The tie clip (lavalier) microphone is detachable and uses a Lemo connector, you can find out more about Lemo connectors for radio microphones here.

The receiver unit has meters to show received RF (radio) and AF (audio) levels, which of the two antennae are active and that the unit is receiving power. Squelch is adjustable by a front mounted pot. Power is supplied by a separate "wall wart" type unit, it is conceivable that you could also power the receiver from a battery supply or vehicle "cigarette lighter" socket for location recording and film work (adapters not supplied).
There are output jacks on the back panel for balanced XLR fixed microphone level or 1/4" jack with a variable line level adjusted by a trim pot.

Two of these units can be locked together and will take up a single unit of rack space, I should be able to find you a suitable tray if this option is of interest to you.

VHF radio mic kit - just £69 for the entire kit including flight case

As there is now so much competition from (in my opinion) cheap inferior equipment from the Far East I have priced these modestly to sell at just £69 for the entire kit, which includes a lightweight flight case. Note that unlike similar systems at this price point found on eBay, this is a true diversity system with two aerials and receiver circuits to guarantee the best possible reception. The aerials can be extended to further improve reception, if you are going to be some distance from a stage or want to locate the receiver inside a rack or shielded control room. If you can find a better deal, drop me a line via the contact page and I will do my best to match it.

It will be supplied in a small lightweight flight case, with padded foam cut outs for the receiver, transmitter, power supply and a couple of batteries. The original hard copy operator's manual will also be included.

Carriage by courier is now included in the price.


UPDATES:

05/11/2016 - Now sold

Saturday, 19 April 2014

For Sale - Gemini P600 P.A. Amplifiers - £49 each

I pulled these amplifiers out of a school p.a. system were they had done about 8 years of constant, if somewhat gentle service. The school had complained that they were becoming noisy in use, read on and you will find out why. For speed, economic and reliability reasons I installed new Samson amplifiers in the school and put these in the workshop as a summer project.
On inspection they were very dusty inside and the bearings had gone on the cooling fans, making them emit a banshee like wail. I thoroughly cleaned them out with a vacuum cleaner and all errant fans were replaced with computer fans of the same size.
They are now whisper quiet, even the attenuators are quiet, so they could be put to use in home studio or used in conferencing or as a standby amplifier for just about any anything requiring a modestly powered amp.

 Gemini P600 - Home studio, conferencing or DJ use

My research would suggest that they can run 85 Watts into 8 Ohms. I used them on a few gigs to drive 10" and 12" vocalist monitor speakers and they worked admirably without overheating or clipping issues. But obviously they wouldn't be first choice for driving a mighty sub-bass system.
That said, most people who read this website are pretty smart and know their stuff, so I shouldn't need to point out that the rating of 85 Watts, is a true R.M.S. value that can be delivered for hours on end without overheating or distortion and not so called "Chinese Watts", which are peak values only possible for milliseconds.
As you can probably guess I am getting very tired of reading adverts on eBay and elsewhere claiming power outputs of 10Kw from a 2U high amplifier fitted with a domestic 13 Amp plug. If you do the math you will soon realise that if such claims were true, the unit would need to be fitted with a cee-form plug and need to be fed off an industrial 63 Amp 3 phase power distribution board.

Gemini P600 - 85 Watts of true, undistorted, R.M.S. power 

The overall package is 4U tall, but shallow, quite the inverse of modern designs and the weight is around 10 Kg. The front panel has an On/Off switch with power indication, there are two large volume control knobs and selectors allowing you to run two sets of speakers independently or simultaneously. The rear panel has 1/4" balanced input jacks or phono unbalanced input jacks. Output is via push terminals. Should it be of use, I have a selection of 19" output panels available for additional cost, sorry I am not a charity.

Gemini P600 - run two sets of speakers independently or simultaneously

If your interest is technical in nature, you can find an overview with the specification sheet here

I have priced these to sell at £49 each, there have been some similar models that I've seen sold on eBay for less, but they were all in ropey looking condition and not cleaned and checked over like these particular units. There are no issues with noise or performance, but do bear in mind that the componentry will be the best part of 25 years old, they will all be good quality components, but even the best capacitors can go out of specification over time.

Feel free to collect, or I can arrange courier delivery within the UK mainland for just £10. Exceptions apply to certain areas; such as the Highlands and Islands and may be subject to surcharges.

Friday, 18 April 2014

Time Out - No peace for the wicked

Well I've been back from my break for just a couple of weeks, but it feels longer! The day I arrived the phone rang and ever since I've been on a mad circuit of various London based financial institutions assisting their conferencing needs.

OneOneTwo.com - out on a mad circuit of various London based financial institutions

This weekend I am on standby, so it is the ideal opportunity to do a spot of Internet catch up. The website is back on line and I have a lot of new items to list, plus some older ones to promote. Watch this space, the next few weeks should be hectic.

Thursday, 30 January 2014

Time Out - A well earned rest

I have been working pretty much non stop for the last 11 months going from project to project and am taking a well earned rest for the next few weeks.

In order to avoid accepting PayPal orders that can't be processed I will be putting the website into "Pause" mode during this period.

If you have any comments or queries in the interim feel free to leave a message on the OneOneTwo Facebook page here and I will do my best to give you an answer. If you are at all curious to find out what I am up to you will find the answer here.

Business as usual will resume towards the end of March and I am looking forward to the next busy season just as much as the forthcoming rest period.

If you want to find out what I am up to you will find the answer here

Wednesday, 1 January 2014

Time Out - New Year and no hangover



It was an unusual New Year's Eve, back doing one of my favourite things, mixing live music and for once at a prestigious location, viz. The Bluebird Cafe, on trendy King's Road, London.

It was a combined New Year's party and wedding reception. It was certainly the poshest private party I've ever worked at, if you didn't have a double barrelled name you weren't on the list. Kudos to the country's elite, they definitely partied like it was 1999.

The funk band were the loudest I've ever had to contend with, leaving about 5 Kw of ElectroVoice sound system teetering on the edge of clipping, yet they still wanted more, more and even more level.

I thought I could relax after midnight when they handed over to the DJ, so I found a cosy couch to relax on and monitor the system in a horizontal position. I'm no slacker but it was 14 hours into the working day by then.

Within minutes my reverie was rudely disturbed by a guest waving his mobile phone at me and asking if I had a lead to fit it? I hunted out a spare charging lead only to be told that it was a sound lead he needed, so he could do an impromptu karaoke number! To be fair, sans rehearsal, he crooned an excellent medley.

As I was driving back, there was no hangover to contend with this morning and my hearing has recovered unscathed. But perhaps I should buy myself a mail order title before the next event?

Mark Kinnon-Deseife (Lord).